Click on the image above to learn more about the M1 Carbine
|
anyone seen a M1 caarbine bolt get shatttered |
Post Reply |
Author | |
JR's GunWorx
Recruit Joined: Oct 28 2017 Location: Glasgow, KY Status: Offline Points: 3 |
Post Options
Thanks(0)
Posted: Nov 04 2017 at 8:44am |
Hopefully the picture uploads. Have a customer who brought in his M1 carbine with a shattered bolt. Blamed steel cased ammo. Trying to verify if such could be the case as I have my doubts.
Anyone else see a bolt get shattered by steel case ammo? Thanks John |
|
Thx
John |
|
Charles
Grunt Joined: Mar 21 2016 Location: Maryland Status: Offline Points: 587 |
Post Options
Thanks(0)
|
I'v been shooting steel casing ammo for years without any problems. Could they have been improperly hand loaded? A dirty left lug has been known to cause a bolt to brake as well. Inspect the area of the action were the left lug would be for burs. Also heavy scraping marks on the left lug. Hope this has been helpful.
Your photos failed to show up. |
|
Charles
Co B 1st Batl.115 Inf. Reg. 29th. Divi. 4.2 Heavy Mortar Co Retired Life member NRA |
|
JR's GunWorx
Recruit Joined: Oct 28 2017 Location: Glasgow, KY Status: Offline Points: 3 |
Post Options
Thanks(0)
|
that's what I suspect also. Not the current owner, yet perhaps some past owner. Yes, found some burrs and rough stops on lug area of the receiver on both sides. Smooth those out. When I tested the fit of a replacement bolt, it operates smoothly and seems to lock up well. Now, if would be great if I can get the extractor to get in place while holding the ejector in. Extractor spring is strong! As it should be.
|
|
Thx
John |
|
New2brass
Moderator Group Dan Pinto, Photo Editor Joined: Nov 29 2015 Location: CT Status: Offline Points: 4627 |
Post Options
Thanks(0)
|
Are you using a bolt tool? Here is an article on doing it without a bolt tool, however it is highly recommended that a bolt tool be used for ones sanity. As linked at bottom of that article is the bolt page at bottom is instructions using bolt tool.
|
|
JR's GunWorx
Recruit Joined: Oct 28 2017 Location: Glasgow, KY Status: Offline Points: 3 |
Post Options
Thanks(0)
|
I noticed that sanity issue without the bolt tool. And as expected, after I ordered a bolt tool, it came together as it should have in the first place. :)
|
|
Thx
John |
|
sleeplessnashadow
Admin Group Joined: Nov 09 2015 Location: SoCal Status: Offline Points: 1150 |
Post Options
Thanks(0)
|
I'm a little late on this one.
It's not possible to determine what may have caused the bolt to shatter without a photo or a detailed description of what broke, where and other details. Steel case .30 carbine ammo isn't going to break a GI bolt. Not even in the long run. You'd have more success trying to beat someone to death with a rubber chicken. It can break the GI extractor over time. "Shatter" implies the bolt broke like glass. The most common break is the right bolt lug breaks off with the crack starting in the opening for the extractor and extending to the point the rear of the right lug connects to the body. One thing that can cause the right lug to snap off is anything that impedes the movement of the left lug as it moves back and forth in the receiver. This puts added pressure on the right bolt lug from the slide as it moves back and forth. Sometimes something as simple as a burr in the path of the left bolt lug is enough to do it over time. Easily remedied by gently filing or polishing the burr til it's gone. Here's an example of the right lug having snapped off due to burrs in the path of the left bolt lug. Half way down the web page on bolts there's an explanation with an additional pic to illustrate why it broke. http://www.uscarbinecal30.com/bolts.html I still have the bolt. Next time I do pics I'll take a few more showing the break from different angles. Same bolt... Jim |
|
manteo97
On Point Joined: Jan 15 2016 Location: Victoria, B.C. Status: Offline Points: 61 |
Post Options
Thanks(1)
|
Have seen a broken bolt like the one in sleeplessnashaodow's post. A customer brought his carbine into me (Dad's bring back Inland), and had broken the original bolt AND a commercial replacement bolt. Barrel had been replaced by a "qualified gunsmith". Receiver was deformed in left bolt lug area too, beyond repair
I checked headspace with the broken bolt and it swallowed the NOGO. Mic'd out the depth of chamber and it was .050 deeper than the NOGO dimension. So, it would seem if the chamber has been reamed way to deep, too much play in the bolt during firing, the spent cartridge recoils back a bit before it slaps against the bolt face (rather than being held firmly in place) and bingo! There goes the right lug. So, if you can, check the headspace with gauges. |
|
bonnie
Recruit Joined: Aug 28 2016 Location: N.C. Status: Offline Points: 89 |
Post Options
Thanks(0)
|
Some times things just break?
Many years ago during a CMP club match a new from rebuild CMP "white bag" club carbine had the right lug break on a flat bolt during a match. Couldn't determine a reason why. It was fitted with a new round bolt and works just fine to this day. |
|
carbinecanuck
On Point Joined: Feb 04 2017 Location: Western Canada Status: Offline Points: 94 |
Post Options
Thanks(0)
|
Just had this 'N14' marked bolt come apart on me this past weekend.
I haven't been playing with carbines for a very long time. I get the impression it is not a very common occurrence. Just some bad luck I guess. The bolt was hot blued post war at some point. Other than that, did not notice any signs of anything unusual about it. The carbine was quite new to me, and I only had a chance to put about a dozen Winchester FMJ through it prior to it failing. |
|
Courage is fear holding on a minute longer. - GEORGE S. PATTON
|
|
floydthecat
Hard Corps Joined: Oct 13 2016 Location: Mississippi Status: Offline Points: 1996 |
Post Options
Thanks(0)
|
I'm sure there are no records anyone is keeping on broken bolts, but I had an N14 crack myself and it seems that the N14 shows up often in discussions concerning cracked bolts. I just steer-clear of any NPM flat bolt. Reading a lot about N14 cracks and having one crack myself, was enough to convince me.
|
|
sling00
Hard Corps Joined: Apr 21 2016 Location: Tennessee Status: Offline Points: 941 |
Post Options
Thanks(0)
|
Sounds like good advise. It would be interesting to have one inspected to determine the failure mechanism.
|
|
W5USMC
Moderator Group Joined: Apr 29 2017 Location: Missouri Status: Offline Points: 2949 |
Post Options
Thanks(0)
|
Yep, that is pretty convincing to me too. I think from now on when I shoot my Postal Meter, I will use a spare bolt instead of the N 14.
|
|
Wayne
USMC Retired NRA Life Member |
|
manteo97
On Point Joined: Jan 15 2016 Location: Victoria, B.C. Status: Offline Points: 61 |
Post Options
Thanks(0)
|
carbinecanuck is sending this broken bolt to me, along with the carbine. I'll be able to do a bit of a metallurgical examination on it. I'll post the results.
|
|
New2brass
Moderator Group Dan Pinto, Photo Editor Joined: Nov 29 2015 Location: CT Status: Offline Points: 4627 |
Post Options
Thanks(0)
|
Hmm, I have a N 14 bolt with a crack.
This is the third mentioned here. coincidence or are we on to something
|
|
GotSnlB28
Hard Corps Joined: Jan 01 2016 Location: WI Status: Offline Points: 892 |
Post Options
Thanks(0)
|
fyi your bolt has its original finish - when manufactured they were dulite finished. Over the years I have seen more than a few posts where other carbine owners experienced cracked N14 bolts. |
|
carbinecanuck
On Point Joined: Feb 04 2017 Location: Western Canada Status: Offline Points: 94 |
Post Options
Thanks(0)
|
I am familiar with the Du-Lite finish.
But this one was hot blued. Along with the rest of the barreled action. I am almost certain of that. |
|
Courage is fear holding on a minute longer. - GEORGE S. PATTON
|
|
carbinecanuck
On Point Joined: Feb 04 2017 Location: Western Canada Status: Offline Points: 94 |
Post Options
Thanks(0)
|
Just took possession of an S.G. mixed parts carbine this weekend. The seller had notified me prior to the sale that the bolt it was coming with, was unusable.
Take one guess as to what marking was on the left lug ..... It seems as this is turning out to be something a bit more than pure coincidence. |
|
Courage is fear holding on a minute longer. - GEORGE S. PATTON
|
|
floydthecat
Hard Corps Joined: Oct 13 2016 Location: Mississippi Status: Offline Points: 1996 |
Post Options
Thanks(0)
|
I hadn't paid much attention to the problem, until I cracked one. It seems as if every where I went I was reading comments concerning N14 failures. The issue has been mentioned on just about every forum I visit. As far as I'm concerned...N14 bolts are only for looking at and not for shooting.
|
|
New2brass
Moderator Group Dan Pinto, Photo Editor Joined: Nov 29 2015 Location: CT Status: Offline Points: 4627 |
Post Options
Thanks(0)
|
I have not done the math to say that there is an issue with these bolts. As a matter of fact there is not enough reports of broken bolts to suggest one is more prone to break than another. A little birdie tells me that you can have one of these bolts.what is interesting is this one is for the ubber rare 1942 NPM |
|
manteo97
On Point Joined: Jan 15 2016 Location: Victoria, B.C. Status: Offline Points: 61 |
Post Options
Thanks(0)
|
A quick review of past CCNL's indicates N14 marked flat bolts were used from Dec '43 to Feb '44 or later based on barrel dates, and other data. This would be roughly 4.1 mil S/N range and higher. NPM made these bolts in-house, apparently the number (8, 9, 11, and 14) indicate drawing and/or design changes. Union Switch & Signal also made UN marked bolts under contract, and these are found towards the later part of production.
So, that kind of indicates maybe 150,000 or more M1 carbines came out of the NPM factory with N14 bolts. |
|
Post Reply | |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You can vote in polls in this forum |