Click on the image above to learn more about the M1 Carbine
|
“Lipstick” Oiler and Other Carbine Tools |
Post Reply |
Author | |
jackp1028
Hard Corps Joined: Jan 01 2016 Location: Cloudcroft, NM Status: Offline Points: 1276 |
Post Options
Thanks(6)
Posted: Mar 16 2019 at 2:26pm |
2019-G “Lipstick” Oiler and Other Carbine Tools By Jack Pickle
Published across the country circa May to August 1944 Though the article says the “Lipstick” oiler is the only maintenance equipment needed for the carbine we know that two other tools inherent to the carbine are required by the soldier for first echelon maintenance of the carbine.
The
carbine oiler was a concept that was first described in Winchester’s
patent number 2,335,357 pictured below The patent described the attachment of a rifle sling using the oiler as an anchor. The oiler itself was not necessarily patentable since it’s concept is somewhat obvious to those familiar to the “state of the art”, a standard for whether something is worthy of a patent. However, the sling attachment concept was deemed novel and therefore patented. The oiler was an integral part of every carbine issued.
Although the enlarged oiler cap shown in the patent drawing may have been the inspiration for the “I” shaped cut out in Type 1 stocks, no such oiler has been found to exist other than a prototype. The slot evolved to the oval shape of later type stocks. Another interesting bit of news in this article was the mention of sperm oil being used in conjunction with the oiler. This may have been unique to Winchester at the time and was short lived because all official USGI maintenance documentation describes the use of a mineral oil rather than sperm oil. According to TM 1276, a “Preservative Lubricating Oil (Medium)” is to be used for conditions above freezing and a “Preservative Lubricating Oil (Special)” is to be used for conditions below freezing. It refers to TM 9-850 (Abrasive, cleaning preserving, sealing, and adhesive, etc.) for specifics of the lubrication. TM 9-850 describes these oils as a “...highly refined, light, very low pour point mineral oil containing a rust-inhibiting additive...”. No mention of sperm oil. There was no mention of any lubricant in the TM lubricant bible that was based on sperm
Here’s a link to TM 9-850:
https://archive.org/details/TM9-850/page/n15
Excessive whale hunting due to lack of regulation led to low prices for whale products, as well as a significant decline in the international whale population. Some species with severe population losses. These factors led whaling companies to recognize the need for regulation. In 1946, 14 nations signed the International Convention for the Regulation of Whaling. This convention established the International Whaling Commission, which was seen as a major precedent for international regulation of natural resources because it gave economics and conservation equal weight. Countries which relied heavily on whaling as part of their economic foundation such as Norway, Iceland, and Greenland, proved difficult to negotiate with in regard to scaling back on whale hunting, but by the 1960s so many species were endangered that a long negotiation process resulted in an international moratorium on whaling by the IWC in 1986. [www.leaf.tv by Shelly Moore]
The two other tools required by the individual soldier for carbine maintenance are barely mentioned in the last paragraph of an article in the Hartford Courant September 4, 1943
Winchester
Makes New Army Carbine The carbine part is the recoil spring guide which can be used to remove hammer and trigger pins and also the hammer spring guide. The other is the rim of the carbine cartridge which conveniently fits the oddly shaped head of the barrel band screw allowing the soldier to field strip the carbine without needing a screwdriver.
Perhaps
being an occupation force soldier in Japan after WW2, Corporal
Johnson was not specifically trained in the care and maintenance of
the M1 carbine before being rushed into combat. At that time in our
country’s history, the armed forces were being drawn down, not
expecting to have to fight another major conflict until North Korea
invaded South Korea across the 38th parallel in June of 1950.
The Carbine Collectors Club Copyright© 2019 www.USCarbineCal30.com This article and/or its images are the property of the author. They're not to be copied without prior written permission (Title 17, Chapter 5, Section 501(a) U.S. Code)
|
|
JackP
|
|
m1a1fan
Hard Corps Got Para? Joined: Jan 01 2016 Location: Virginia Status: Offline Points: 1736 |
Post Options
Thanks(0)
|
Jackp, excellent article!
Never really thought about an oiler other than whether a carbine had one or not, until now. Even something as "simple" as an oiler had engineering and documentation like TM's behind it. Thanks! (and Dan too)
|
|
jackp1028
Hard Corps Joined: Jan 01 2016 Location: Cloudcroft, NM Status: Offline Points: 1276 |
Post Options
Thanks(0)
|
It turns out that the "Lipstick Oiler" was also used on the M3 and M3A1 submachine gun. The earlier M3 had a clip on the left side of the receiver that could hold the standard M1 Carbine oiler.
The later M3A1 variation of the submachine gun had the clip removed and the oiler was incorporated in the grip. This necessitated the redesign of the cap to fit into the grip. This new oiler design came about in December of 1944 so it was never considered for use on the carbine and was not the source of inspiration for the "I" shaped oiler slot. By the way, the oiler stylus could also be used as a drift punch for removing pins on both the M1 carbine and M2/M3A1 submachine gun. |
|
JackP
|
|
sling00
Hard Corps Joined: Apr 21 2016 Location: Tennessee Status: Offline Points: 941 |
Post Options
Thanks(0)
|
The oilers pictured above appear to be those made for the M2 Hyde-Inland sub machine gun. Developed and limited manufacture during 1942-1943 and cancelled after adoption of the M3 "Grease Gun" in 1943. They are similar in size to the M1 carbine except for the oversized cap.
|
|
jackp1028
Hard Corps Joined: Jan 01 2016 Location: Cloudcroft, NM Status: Offline Points: 1276 |
Post Options
Thanks(0)
|
@sling00. Thanks for the correction. After further research I learned that the M3A1 oiler is actually a little bottle captured with a jam nut inside the grip. It looks like the cap and stylus are totally different than either the M1 carbine or the M2 Hyde caps. I refer to your earlier post.
http://www.uscarbinecal30.com/forum/very-early-i-cut-oiler_topic2819.html |
|
JackP
|
|
W5USMC
Moderator Group Joined: Apr 29 2017 Location: Missouri Status: Offline Points: 2959 |
Post Options
Thanks(1)
|
Great article, JackP! Very interesting, and I will say that I am not putting any sperm oil on any of my Carbines!
|
|
Wayne
USMC Retired NRA Life Member |
|
jackp1028
Hard Corps Joined: Jan 01 2016 Location: Cloudcroft, NM Status: Offline Points: 1276 |
Post Options
Thanks(0)
|
@Wayne, did you know there's a big difference between sperm oil and whale oil. Sperm oil was extracted from the spermaceti organ of the sperm whale whereas whale oil was just boiled down blubber. Betcha didn't know that!
|
|
JackP
|
|
W5USMC
Moderator Group Joined: Apr 29 2017 Location: Missouri Status: Offline Points: 2959 |
Post Options
Thanks(0)
|
JackP, No actually I did not know that and I am not really sure that I will ever use this new found information ever again in my Life.
|
|
Wayne
USMC Retired NRA Life Member |
|
New2brass
Moderator Group Dan Pinto, Photo Editor Joined: Nov 29 2015 Location: CT Status: Offline Points: 4660 |
Post Options
Thanks(0)
|
look up sperm oil
The spermaceti was in the head. Its properties would have been beneficial In cold temps. It was used in as a steam oil, lubricant in steam engines. Also good for machinery.
|
|
Donnie
On Point Joined: May 31 2018 Location: Newburgh, IN Status: Offline Points: 336 |
Post Options
Thanks(0)
|
Mr Pickle, thank you for such fun and informative article on that curious little component. Nice work!
|
|
Post Reply | |
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You can vote in polls in this forum |